NewBeeDrone BeeBrain BLV4 AIO Flight Controller/ESC - Choose Receiver

Attention! The BeeBrainBLV4 OSD might not be compatible with third party cameras. If you are planning to use it for a customized build, please be aware it only supports the cameras below:

• NewBeeDrone BeeEye Camera
• Runcam Nano4

Specifications

BeeBrain BLV4 ELRS:

• MCU: STM32F411
• ESC Firmware: S-H-40 - Bluejay, 0.16, 48kHz.
• ESC Specifications: 4 channel 12A ESC
• ESC Connector: JST-1.0 3Pin
• NBD OSD (Betaflight OSD Compatible)
• Weight: 6.5 grams (including antennas and battery connector)
• Size: Outer dimensions 29 x 29 x 7.6 mm
• Holes: 25.5 x 25.5 mm
• Battery input: 1S
• Connector: PH2.0
• UART2 TX and RX for onboard EXPRESSLRS receiver (SX1280)
• UART1 TX and RX free
• VTX Adjustable power: 5mW-25mW-SmartMAX. SmartMAX will automatically adjust the VTX power according to the board temperature. When the board temperature rises, the VTX power will be automatically reduced. When the temperature is low, the maximum output power can be up to 400mW

BeeBrain BLV4 GHOST:

• MCU: STM32F411
• GYRO: BMI270
• VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX(SmartMax up to 400mw) with BeeTX 5.8Ghz Antenna
• ESC: 12A BLHeliS Pre-Flash with Bluejay 0.18 target: S-H-40 48kHz
• ESC Connector: JST-1.0 3Pin
• OSD: NBD7456 Graphical OSD compatible with Betaflight OSD
• Receiver: GHOST 2.4G receiver with GHOST 2.4G qT Antenna
• Flight Controller Weight: 6.5g(Include antennas and battery connector)
• Flight Controller Size: Outer dimensions: 29x29x7.6mm
• Flight Controller Holes: 25.5x25.5mm
• Battery input: 1S
• Uart2: Tx for GHOST 2.4G Receiver
• Uart1: Tx&Rx free
• Power Connector: NBD-PH2.0 connector

Includes

BeeBrain BLV4 ELRS

• 1 x BeeBrain BLV4 Flight Controller w/ ELRS
• 4 x Grommet
• 4 x Screw
• 1 x Receiver T-Antennas
• 1 x Receiver Antennas
• 1 x VTX Antenna

BeeBrain BLV4 GHOST

• 1 x BeeBrain BLV4 GHOST Flight Controller w/ GHOST
• 4 x Grommet
• 4 x Screw
• 1 x qT Antenna
• 1 x VTX Antenna

Firmware

BeeBrain BLV4 ELRS:

• BeeBrain blv4 ELRS3.0 receiver firmware
• BeeBrain blv4 ELRS2.0 receiver firmware
• BeeBrain blv4 ELRS Betaflight 4.4 firmware

BeeBrain BLV4 GHOST:

• BeeBrain BLV4 GHOST Betaflight 4.4 firmware

All firmware can be found on NewBeeDrone Github Page.

Note: For the ELRS variant, during the binding process, power up the drone 3 times; on the third time you plug in power, the ELRS Receiver will get into binding mode. We are still trying to work on the ELRS firmware and make it able to just click the boot button to get into bind mode. We will update this in the near future. Check out the video below by CiottiFPV to see how to get into bind mode. Thanks, bro, for showing this. lol